Your cart is empty.
Your cart is empty.Product Description
High-quality materials：
It is made of high quality YG6X alloy as raw material. The process of oxynitriding of the cutter head strengthen the drill hardness.
Cross cutter head design：
More accurate positioning, less resistance,
1/4 inch hex shanks：
This size perfect fit for all Impact driver/drill chucks, Non-Slip hex shank handle drill bit design for hex shank can clamped on the drill more firmly
Special note
Tool: Power drill.hand drill.charging drill. Do not use impact mode of drill or hammers
This product cannot be used for drilling toughened glass and drilling of pure concrete
When drilling, use only flat drill function, do not use any impact force
When drilling fragile items, the drilling speed is not too high, the pressure should not be too large, so as not to damage the drilled items
Wide Application:
Professional glass and tile drill bits provide smooth and accurate drilling in ceramic tiles, marble, thin iron plate, mirrors and glass. Remember to add Water or coolant when drilling.
Attention：
When drilling hard material (glass, porcelain floor tile, marble or granite), please using water for lubrication.
Vince Abelardo
Reviewed in Australia on February 7, 2024
These drill bits are a waste of money. Supposed to be made for Masonry - Tile, Brick etc. Half a hole in, the head broke off in the brick meaning the hole could not be used. Very disappointing outcome. I expected at least 3 to 4 holes before it wore down - never expected it to break off???
Greg A
Reviewed in Canada on February 20, 2024
Good quality drill bits. Will def buy again. AAAAA+++++
Se me quebraron al usarlas
Reviewed in the United States on April 9, 2024
El producto lo utilizamos para perforas y al hacerlo se quebraron d las puntas
landofhappiness
Reviewed in Canada on July 30, 2023
I ordered this to drill into a concrete wall to install a TV mount and it did the job. I also used it in metal and it did the job. Very good product.
Victor Julio Hernandez
Reviewed in the United States on July 21, 2023
Pastor Kenneth R Wilson Sr
Reviewed in the United States on April 17, 2023
They do the job that I needed to get done.
Megan Coronado
Reviewed in the United States on September 6, 2022
After just 2 holes on bricks for my Ring doorbell there was very noticeable damage to bit ( see picture comparing new and used ). Worked for what I needed. Will not recommend for repeated uses.
Autos Compactos San Antonio
Reviewed in Mexico on May 29, 2022
Las tuve que regresar. ElKit me llegó mal, 4 de 5mm y 4 de 6mm. Probé la de 6mm, pero se necesita hacer mucho esfuerzo para que perfore, en mi caso azulejo, solo sirvió para 2 perforaciónes, laBroca se rompió en la 2da perforación.
Jesús cruz Vidal
Reviewed in Mexico on January 9, 2022
Pensé que seria como las brocas tradicionales al momento de taladrar un muro de mosaicos, pero sorpresa, no se movió en lo absoluto del punto a perforar y penetro fácilmente
boofay
Reviewed in the United States on May 29, 2021
Used these drills to make holes in tiled shower to install heavy sliding glass shower door. The first hole went smoothly but the second one not so well. We did not use heavy pressure. Had to use water spray to do the next couple holes. Drills may not work for long term use. Did what we needed for our DIY project.
Orville Thompson
Reviewed in the United States on March 5, 2020
Used them for mounting LED sun powered lights to our rock wall. The smaller bits burned up but the larger bits worked fine. I probably needed a flow of cooling water and the smaller bits would have worked fine too.
SapperActual
Reviewed in the United States on February 9, 2020
I purchased these in order to drill through my side yard cement slab in order to secure my 10' gate. I DO NOT have a hammer drill and assumed it would be quite a bit of work and require that I gradually increase the bit size to achieve the 1/2 diameter hole needed. I was wrong. With my Milwaukee M18 FUEL driver, I had the hole finished in under 20 seconds. I didn't even have to cool the bit with water. I would highly recommend these masonry bits. I can't speak to longevity as I only needed one hole drilled but the bit is still sharp and minus some removed paint, it looks good as new.
Richard A.
Reviewed in the United States on February 29, 2020
I'm using these bits to drill a 10mm hole in the bottom of a wine bottle. I use the 3mm bit first to make a starter hole then open the 3mm up to 10mm. I've drilled over 30 bottles with no problems at all. Just remember to use LOTS of water!!! I use a bucket of water with a small fountain pump to flood the bit while drilling. Keeping the bit and glass cool is the key to success.
Recommended Products