Your cart is empty.
Your cart is empty. Function
Amplify the red, green, blue three group signal of 3 channel controller, improve the system with load capacity, and has minimal delay, but can keep synchronism in cascade.
The outlet should be connected correctly according to the color shown in the wiring diagram.
Can't be wrong attached, in order to avoid short-circuit.
Specification
Working temperature£º-20~60¡æ
Input voltage£ºDC12-24V
Signal voltage: DC 12V-24V
Input signal: RGB common anode PWM dimming signal
Dimension: L145*W76.8*H20.6mm
Output£º3 channel
Connection mode: Common anode
Output current: max 8A (each channel) Output power: max 288W(12V), max 576W(24V)
Delay time: 20NS
Package included:
1pc * RGB high speed power Amplifier
Allan
Reviewed in Canada on March 5, 2025
It works, my RGB LED strip lights I have that go around my entire house roof line quit partially working. I lost the blue light output which affects most of my other colors when mixing. So the part is identical to the one it replaced except my old one was white. Installed it and tested the three main colours then white light, all working good. It's a metal case if you wondered. I took the old apart and found a part which appears to be for cooling had come loose and may have been shorting out, my blue wire looked like it had gotten hot it was discolored.
Ethan
Reviewed in the United States on February 12, 2021
Works exactly as intended, boosts and repeats signal perfectly. I'm using this to boost from my 4pin 12v RGB header on my motherboard to sink to my 24v LED wall panel, works fantastic.
I Gonzalez
Reviewed in the United States on March 30, 2020
Absolutely awesome! Very responsive RGB amplifier and can power a good amount of LED’s, I’ll be ordering a 2nd one soon. This was installed in one of my limos go power under glow and wheel RGB light.
Freshh
Reviewed in the United States on May 24, 2017
Simple to use, works without any problems. LED power indicator is a nice feature to make sure the AMP is receiving power.You need a DC power jack female plug adapter to provide power to the AMP from a power supply.Used it to connect to LED strips from each other, no fade in color down the strips.
Victor
Reviewed in the United States on October 18, 2017
I purchased 2 of these for one of my show cars. Excellent product and a great value. I have had these is use now for several months. One time, I did have the color change from the set color - Red, to a Fuchsia for no reason. After it had been shut down for a while it came back on correct. Other RGB strips running on the same controller were not affected, only the ones running on one of these amplifiers. It only happened one time so not overly concerned. I would definitely recommend and would buy again. In fact, I am considering putting one of these in a watertight box and using a diode bridge rectifier and a landscape transformer to control some long runs of RGB LED strips around my decks.
Lynne Miller
Reviewed in the United States on February 22, 2016
Excellent device with plenty of overhead. I needed to hook two 24v 32ft strands together, but was not thrilled about the prospect of delay between the strands from running them end to end with this in the middle. I instead installed this device directly after the controller box, and then ran both strands directly from this amplifier. Two months and no problem, and the best part is that both strands are 100% in sync with each other...no delay! Well made, extremely easy installation, and the unit does not get warm (and is well beneath its maximum current rating) with two full-size 24v strands attached. The price is sweet too. ...Just wanted to review this to be sure that folks know that you don't have to install this between strands. You can install it after the controller and run both strands directly from it to avoid delay. I had to do a ton of research before ordering, and wished somebody else had mentioned this in a review.
Mr. Toad
Reviewed in the United States on September 3, 2015
I used this to connect a second strip of 5050 RGB LEDs, syncronized with my first set. This unit made the job very easy and straightforward. It works reliably with the strips powered with 24 Volts. My only complaint is that the Green channel seems like it is not quite properly calibrated, so certain colors are not replicated accurately on the second LED strip. Of course, the LED strips could be from different production lots that have different illumination biases--I don't know for sure. Regardless, for my purposes this unit allows me to connect enough lighting to fully wash the front of my house with synchronized light color and brightness, all controlled from a single remote.
JP
Reviewed in the United States on June 23, 2015
Works very well, does not heat-up, delay not noticeable. Well priced and well made.
Cesidio V. Barberis
Reviewed in the United States on October 16, 2015
Worked exactly as advertised. Did not even heat up noticeably. very solid case.
Recommended Products
